top of page
Search
How to Inspect Tyre Tread Before It Costs You

How to Inspect Tyre Tread Before It Costs You

Writer: hopeautomotive
hopeautomotive
4 days ago
6 min read

A tyre can look fine from the driveway and still be worn where it matters most. Knowing how to inspect tyre tread takes only a few minutes, but it can help you avoid poor wet-weather grip, a failed roadworthy check, uneven handling and the cost of replacing tyres before their time.

For Gold Coast and Brisbane drivers, regular tread checks make sense. Heat, heavy rain, stop-start traffic, long motorway runs and the occasional rough worksite track all affect tyre wear differently. Check your tyres once a month, before a long trip and any time the vehicle starts pulling, vibrating or feeling less settled on the road.

How to inspect tyre tread properly

Park on level ground, apply the handbrake and turn the steering wheel so you can clearly see the front tyres. On many vehicles, you will need to look behind, underneath and across the full face of each tyre. A torch is useful if the vehicle is parked in a garage or shade.

Start by looking at the tread pattern across the tyre, not just the outer edge you can see at a glance. The grooves should be clearly defined and the tyre should wear evenly from the inside shoulder to the outside shoulder. Check all four tyres, plus the spare if it is fitted underneath the vehicle or stored in the boot.

The legal minimum tread depth in Australia is 1.5 mm across the main tread area. That is the absolute limit, not the point to wait for. Tyres with low tread can struggle to clear water, which raises the risk of aquaplaning in a Queensland downpour. Replacing them earlier can be the safer call, particularly if you do regular highway driving, carry tools or tow a trailer.

Find the tread wear indicators

Most modern tyres have small raised bars moulded into the grooves. These are tread wear indicators, sometimes marked by small triangles, the letters TWI or a tyre brand symbol on the sidewall. Follow the marker across to the groove and find the raised bar.

When the surrounding tread is level with that bar, the tyre has reached roughly 1.5 mm and needs replacing. Check several indicators around each tyre. One section may be worn down while the rest of the tread still appears acceptable.

A tread-depth gauge gives a more accurate reading and is inexpensive, but the wear indicators are a reliable first check. The old coin test can offer a rough visual guide, but it is not precise enough to judge whether a tyre is legal or safe. If you are unsure, have a mechanic measure it properly.

Check the inner and outer shoulders

Uneven wear tells you more than tread depth alone. Run your hand carefully across the tread surface, feeling for raised and lowered sections. Then inspect both shoulders - the areas where the tread meets the sidewall.

Wear on both outer shoulders often points to underinflation. An underinflated tyre flexes more, creates extra heat and wears its edges faster. It can also increase fuel use and make steering feel vague.

Excessive wear through the centre of the tread can indicate overinflation. The tyre rides more heavily on its middle section, reducing the contact patch available for braking and cornering.

If one shoulder is wearing faster than the other, wheel alignment or suspension condition may be the issue. This can happen after hitting a pothole, clipping a kerb or regularly travelling on uneven job sites. Simply fitting new tyres without addressing the cause can mean the same expensive wear pattern returns.

Signs your tyres need attention sooner

Tread depth is only one part of a tyre inspection. A tyre can have legal tread remaining and still be unsafe due to damage, age or irregular wear. Keep an eye out for these warning signs:

  • Cracks, cuts, bulges or splits in the sidewall

  • Nails, screws or other objects lodged in the tyre

  • Cupping or scalloped wear across the tread

  • Vibration through the steering wheel or vehicle floor

  • A vehicle that pulls left or right on a straight, level road

  • Frequent pressure loss or one tyre consistently sitting low

Bulges deserve immediate attention. They can indicate internal tyre damage, often caused by a hard impact, and a bulging tyre should not be treated as a wait-and-see problem. Avoid driving on it unless necessary to get the vehicle safely off the road and arrange an inspection.

Cupping, where the tread develops uneven dips around the tyre, can be linked to worn shock absorbers, wheel balance issues or suspension faults. You may notice a droning noise that gets louder with road speed. It is easy to blame the tyre, but the tyre may be showing you that another component needs attention.

Use the right tyre pressure before judging wear

Before deciding a tyre is worn unevenly, check its pressure cold. That means before a long drive, not just after pulling into the servo. Use the pressure listed on the vehicle placard, usually found inside the driver's door opening, behind the fuel flap or in the owner's manual. The number printed on the tyre sidewall is not your vehicle's recommended running pressure.

Pressure requirements can change when carrying a load, towing a caravan or trailer, or setting up a 4x4 for off-road use. A ute loaded with tools may need a different rear pressure from the same ute driven empty on the weekend. Follow the vehicle manufacturer's load advice and adjust tyres only when you understand the operating conditions.

Do not forget the spare. A full-size spare with plenty of tread is no help if it is flat, cracked or ten years old. Check its pressure and condition during your regular inspection so it is ready when you need it.

When tyre wear points to a mechanical problem

Tyres are often the first visible sign that something underneath the vehicle needs work. Alignment problems can wear tyres quickly, but alignment is not always the root cause. Worn steering components, damaged bushes, weak shocks, sagging suspension or wheel bearing issues can all affect how the tyre meets the road.

That is why a quick alignment is not always the complete answer. If a tyre is feathered - smooth in one direction and sharp when you run your hand the other way - a proper inspection of steering and suspension parts is worthwhile. The same applies if wear is severe on only one tyre or appears suddenly after an impact.

For 4x4s, vans and work vehicles, uneven wear can also be accelerated by heavy loads, lift kits, larger tyres or regular gravel-road travel. There is no one-size-fits-all wear pattern. The useful question is whether all tyres are wearing consistently for the way your vehicle is used.

How often should you rotate tyres?

Tyre rotation helps spread wear more evenly, especially on front-wheel-drive vehicles where the front tyres handle steering, braking and driving forces. A common interval is around every 10,000 km, but the correct pattern and timing depend on the vehicle, tyre type and whether the tyres are directional or staggered.

Some tyres must stay on a particular side of the vehicle, while others can be rotated in several patterns. Check the tyre markings and vehicle handbook before swapping them around. If you are replacing only two tyres, fitting the newer pair to the rear is generally recommended for better stability in wet conditions, even on front-wheel-drive cars.

Tyres on an all-wheel-drive vehicle need extra care. Large differences in tread depth between tyres can place stress on the drivetrain in some models. Check the manufacturer's limits before replacing a single tyre or mixing tyres with significantly different wear.

Make tread checks part of normal vehicle care

A quick monthly check is easier than dealing with a roadside puncture or discovering bald tyres before a family trip. Take a look while washing the car, checking engine oil or loading gear for the weekend. If the tread bars are close, the wear is uneven or something does not look right, get it checked before the problem gets more expensive.

Hope Automotive can inspect tyre wear alongside suspension, steering and general maintenance at your location across the Gold Coast and Brisbane. You will get plain-English advice on whether the tyres need replacing now, what may be causing the wear and what should be fixed first.

 
 
 

Comments


© 2023 by YOU DRIVE IT WE FIX IT.​ Proudly created with Wix.com

  • facebook-square
  • Google Square
bottom of page